Home > Problem With > Problem With Foxconn RAID Setup

Problem With Foxconn RAID Setup

The above sounds like you just need to install graphics drivers. I much prefer to have the fan there than not, though a heat-pipe solution would be preferable. This system is quiet. It is not very often you want to complain about your online store being too fast. check over here

Consider RAID I ordered a Maxtor 250 GB 1.5 GB/sec SATAI hard drive and realized an hour later, I needed a second drive since I wanted to try out RAID. I rebooted the computer and noticed that the BIOS RAID screen showed RAID 0 as failed and RAID 1 as degraded. I'm wondering whether I'll need to reflash the BIOS because I can't see RAID controller in the Device Manager list under Computer Management. That is somewhat surprising considering that I am still learning the hardware side of computers, my previous experience with new setups and the immature nature of the Conroe motherboards. https://forums.techguy.org/threads/problem-with-foxconn-raid-setup.792513/

solved Setup help to read already configured RAID 0 HDD's (OS is on SSD): ASUS X99 Deluxe 3.1 mobo with 2 Maxtor7L250S0 HDD's solved How to setup Raid 1! make firefox snappier? I really wanted the DS4 and not the DQ6, but that motherboard was not available in North America as of late September 2006. Oh yes - one more thing.

  1. My requirements were listed from top to bottom in order of most to least importance.
  2. I had originally thought that there was no way to know which DIMM slot was number one.
  3. The pushpin is really a push-pull-pin design.
  4. The other is a single SATA drive connected directly to the motherboard controlled by Sil3112 SATA RAID Driver that came with the Foxconn motherboard K8S755A.

I stumbled across the fact that the drive was still under warranty. Filed under: driver, problems, raid, controller, k8s755a 05-28-2009 11:29 PM In reply to Solution: Problem recognizing hard drives setup in RAID Array Check Device manager under Hardware (Control Panel, System) and Yes, my password is: Forgot your password? Improper installation of the heat sink / fan can lead to processor failure, so it is important to get this right.

I realized that to clarify the choice, I needed to put on paper my requirements and match them against the vendor specs. I am currently using the top setting in the table with the voltage set at +.30 V and the system is stable. In addition, the multiplier, which I have no control of in the BIOS, shows 8.0 in the POST screen and 8.5 in Fox One. click resources how to set up raid 1 with what i have Looking to set up RAID 1, need help Have 2 1 TB HDDs should i set up raid Basic RAID 1

andrewsvalesen Hardware Repairs and Troubleshooting 2 06-17-2007 12:56 PM RAID 5 issue Chveu Hardware Repairs and Troubleshooting 1 04-04-2007 04:13 PM LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Same thing goes for scrolling up and down pages in my browser or in a Word document, it just has that lag before it reacts to any input. I pulled the burner and moved the jumper to master and placed it on the second PATA channel with a different cable. I have raid 0 set up I have windows 8.1 with Ubuntu 14.04 I can boot to both just fine but I have to do it in the uefi bios How

I won't discuss 5 and 10 since for almost all desktops, this is far too expensive to implement and is way beyond the needs of most users. What is going on here? CANT EVEN GET TO BIOS. I wish I knew, bro.

I attempted to do some minimal overclocking without much success at all. http://dotbowl.com/problem-with/problem-with-c1-01-1.html I HAVE TO UNPLUG MY HARD DRIVES JUST TO GET TO BIOS! Port 22 Connection Refused. If you are on a budget, you may find the price a little bit much, but certainly in line with similar Core 2 Duo motherboards.

Except for the stupid things I did during the setup and install and the clear CMOS misinformation in the manual, this install went without a hitch. During high demand this summer it has occasionally sped up to provide instant cooling. I knew what I was buying and what it does. http://dotbowl.com/problem-with/problem-with-avg-14.html Kategooria Teadus ja tehnoloogia Litsents Standardne YouTube'i litsents Kuva rohkem Kuva vähem Laadimine ...

Option 2 would be for RAID multiple drives, which you are no longer doing. All essential data that you don't want to lose should go here. The CPU frequency times the multiplier of 319 * 8 = 2552, or 2.552 GHz, so I trust the POST screen values rather than the Fox One values.

Read speeds are faster.

iMoose said: ↑ (wow, this turned out kinda long 'eh?)Click to expand... I also tried changing the RAID settings to IDE, and although it worked thereby allowing me to install my OS, it was at the cost of significant performance loss. If this is correct, the DRAM frequency is not 1019, but 799. Possible camera?????

Wow, this thread is revived after a long time. In the Intel Matrix screen, create one mirrored volume OR one striped volume for a mirrored setup OR a striped setup. My system is now reaaaaaaally slow compared to what it used to be before I did the WinXP reinstall with the IDE settings. have a peek at these guys I had a choice to go back to a non-RAID hard disk setup after the hard drive failure but I didn't.

I immediately went into the BIOS and changed the DDR voltage to add +.30 Volts. Create a Shutdown/Sleep/Restart or Continue Icon For the Vista Desktop What is a computer guy doing with home remodeling projects on his Website? Tech Support Guy is completely free -- paid for by advertisers and donations. Update Dec 7, 2006: One of the sticks of OCZ RAM tested bad in Vista RC1 memtest.

The drivers are needed by the Windows setup in order to see the RAID volumes so you can set up or choose the partition to install Windows. Changes to the Windows 7 Taskbar You Should Know About Vista Image Capture 'Slipstream' SP1 and SP2 into a single Vista install disc Detailed Instructions for Reverse Integrating SP1 and SP2




© Copyright 2017 dotbowl.com. All rights reserved.