Home > Hp Printer > Printer With No Power

Printer With No Power

Contents

The bad news is, its the printer's motherboard that is damaged. Instead, I get an error message simply saying "the printer is not ready." (at first, I was getting a message that "the printer is offline", but I was able to toggle I am tempted to apply the 3v to pin 5 with the PSU connected to the printer to see if I can at least get the error codes and address the Thanks again for the speedy reply. this contact form

To obtain a replacement power cord, go to the HP Parts Store. Newer models... Do not use a power strip or surge protector. Slide the battery cover into its slot, and then make sure the left side of the cover clicks into place. http://support.hp.com/us-en/document/c01321436

Canon Printer Won't Turn On

If the indicator light was on prior to connecting to the printer but turned off when connected, you might need to replace the power cord. Page 1 of 2 12 Last Jump to page: Results 1 to 10 of 12 Thread: Canon printer - no power up Thread Tools Show Printable Version Subscribe to this Thread… On the cover you will see a small silver hex-head screw. SUBSCRIBEAs low as $1.00/week Home Local In Local Neighborhoods Houston & Texas Traffic Weather Education Politics & Policy Election 2013 Chronicle Investigates Obituaries Staff Blogs Reader Blogs Columnists Opinions & Editorials

  1. Ask !
  2. On the cover you will see a small silver hex-head screw.
  3. If they are all dead = usually a blown fuse and/or over-aged/blown PSU capacitor or two.
  4. Reply to bjwest1977 Incandescent1Jun 11, 2016, 9:39 AM This worked for my XP-700 which wouldn't power on after we had the smart meter installed.
  5. I directly re-connected the circuit board to the dangling white connector hanging from the printer.
  6. Thank you Timroperco for pointing me in the right direction.
  7. I checked the cord and even tried another new one but neither works.
  8. If the indicator light is off, continue to the next step.
  9. All other equipment fired up OK except the Canon IP4500 printer.
  10. caution: Do not replace a power module when an indicator light is lit.

No, create an account now. Find a power cord with the same connectors as your printer power cord, and then use the new cord to repeat the step to Reset the printer and test the wall Main Sections Technology News Reviews Features Product Finder Downloads Drivers Community TechSpot Forums Today's Posts Ask a Question News & Comments Useful Resources Best of the Best Must Reads Trending Now Printer Won't Turn On Brother Replace the power cord.

LuisTutorialTV 225.134 weergaven 8:04 My printer wont print FIX! Hp Printer Won't Turn On I am sure the error lies in the placement of this white wire. But we need your help. The power light came on and the printer started making noises.

PCWorld Home Forum Today's Posts FAQ Calendar Community Groups Albums Member List Forum Actions Mark Forums Read Quick Links View Forum Leaders Who's Online What's New? Hp Printer Will Not Turn Off Yes, my password is: Forgot your password? HP Printer Support 187.612 weergaven 10:44 Printer won't print - Duur: 2:29. However, following a power outage, I couldn't get it to turn on.

Hp Printer Won't Turn On

TheDIYpc 99.484 weergaven 2:29 Fixing a Carriage Jam - HP Deskjet 3050 All-in-One Printer - Duur: 14:46. Ask a question and give support. Canon Printer Won't Turn On Stand up for your right to repair. Epson Printer Won't Turn On I assumed the power outage had caused a surge, possibly blowing an internal fuse.

Send PM SHARE: + Post New Thread Similar Threads Printservers & Canon printers By contink in forum Hardware Replies: 21 Last Post: 28th January 2008, 01:09 PM Create Printer on weblink Remove the small case piece on each side of the paper tray. YES I am a Numpty. Perhaps the power cord was loose from the prongs, or perhaps the wire connector wasn't seated properly before. Hp Printer Power Supply Problems

I bought the "Canadian" version of this discontinued printer specifically for it's CD printing capabilities. The Fair Repair Act, known as S618, requires manufacturers to provide owners and independent repair businesses with fair access to service information, security updates, and replacement parts. Laden... navigate here Thank you!

But I did it in less than 2 minutes. My Hp Printer Keeps Turning On And Off My iP4500 is only 18 months old and rarely used, although I leave it on all the time. With the cables off, press and hold the power button down4.

Does this problem sound familiar to anyone?

es Lamentamos las molestias. Mar 8, 2013 #15 MrTechnik TS Rookie I also just found this thread via google and I have problem with Canon MP630. If the external power module has an indicator light, check the light. Hp Printer Power Supply Replacement I also found info online about "resetting the Pixma back to factory defaults", but it assumes the printer at least powers on.

Probeer het later opnieuw. Sign Up Login Add Question unknown asked Nov 22, 2004 at 8:40pm 0 HP Color Copier 120 Printer won't turn on I have a HP deskjet 6122. After the usual warm-up noises, the thing is printing perfectly again. http://dotbowl.com/hp-printer/printing-a-french-e-on-power-up-of-printer.html The switch module may be shared with the Deskjet 3820.

LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread!Add Thread to del.icio.usBookmark in TechnoratiTweet this threadShare on Facebook!Reddit! TechSpot Account Sign up for free, it takes 30 seconds. Canh Tran 51.230 weergaven 10:36 Fixing Paper Pick-Up Issues - HP LaserJet 1020 Printer - Duur: 6:04. Tell them you believe repair should be fair, affordable, and accessible.

It was dead. But I decided I had nothing to lose ... I cannot figure out how to take it apart to check the main on/off switch. I can get a new main logic board but would hate to replace it only to find its not the faulty part.

So I don't think that's it.Got both 18VDC and 32VDC at the power outputs.The front buttons do not seem compromised.Anything else to check?Thanks, by Jeff W. We have a chance to help the environment and stand up for local repair jobs—the corner mom-and-pop repair shops that keep getting squeezed out by manufacturers. I think. I immediately shut it down, then re-assembled the module and re-installed it in the printer.

Deskjet 6122, Removing the case 1. Was this answer helpful? Adalsteinn Bjarnthorsson 26.074 weergaven 3:11 Why is my printer not working? - Duur: 5:56. Z7_3054ICK0KGTE30AQO5O3KA3016 hp-feedback-input-portlet Actions ${title} Loading...

I don't think that my printer is broken because I was the only one who used this. there is no hex screw on mine (I have a different model Pixma I guess) and so I could not get the module open...so, I went with your take it apart, by Timothy Smithee Faulty cords may cause a printer to not turn on.




© Copyright 2017 dotbowl.com. All rights reserved.